corner
corner
LANCS INDUSTRIES
Providing radiation shielding products and solutions since 1974.
containments and Glovebags
 
Glovebags, Miscellaneous Bags, Containments (1,2)
Catch Containments, Containment and Tent Accessories

 
Glovebags are flexible containments that enclose a contaminated item or form a small work area to confine the spread of contamination. For use under components to capture drips or leaks, Catch Containments (also Drip Bags, or Drip Pockets) can help prevent the potential spread of contamination. Properly designed Work Tents will reduce cross-contamination from work being done on structures or spaces contaminated by radiological or other hazardous materials.

Glovebags

Glovebags are flexible containments that enclose a contaminated item or form a small work area to confine the spread of contamination. Glovebags allow work to be performed on potentially contaminated items by personnel wearing a minimum of protective clothing. Access to the glovebag interior via gloved sleeves enables repairs or manipulations without directly contacting contaminated surfaces. Lancs makes a wide variety of glovebags with different configurations and dimensions. These designs have been developed throughout many years of experience with the U.S. Navy nuclear program, electrical utilities, and DOE lab facilities.

Review the following standard glovebag designs for one that fits your needs. Lancs will gladly work with you to modify any design or dimension in order to satisfy unique requirements.

The glovebags shown are fabricated with the following general characteristics:

Main body:
12 mil or 20 mil clear PVC or Polyurethane, fire retardant

Glove sleeves & access sleeves:
8 mil or 12 mil translucent yellow PVC or Polyurethane, fire retardant

Tie-off points for support:
1" dia disk with light duty injection molded PVC eyelet

Assembly:
Assembled by means of radio frequency heat sealing to ensure highest quality construction. Inflation pressure tested to verify containment seam integrity.

Note: Images show sleeves with sealed ends for illustrative purposes only. Actual items have
open sleeves.

         
  LI-300-BOB Glove Bag   LI-300-BOB

  • Bag-In/Bag-out Bag with internal mitts/gloves. Various sizes, diameters and lengths. Made from PVC or Polyurethane.
  • Flexible HEPA filter option if required.
  • The bag in/out bag has shock/bungee cord located in the hem of the open end that fits into a rib around the bagging ring/port of the filter housing.
  • When the door is opened/removed, the bag provides a barrier between operator and contaminated filter
  • Each bag includes 3ea built-in glove sleeves/mitts to facilitate the filter change
 
         
 
         
    LI-300-363624

  • Glovebag, 36″L x 36″W x 24″H
  • Press-lock zipper or Velcro Split running length of bag
  • Tie-offs welded around perimeter for securing to frame
  • 1 set of glove sleeves and dump sleeve on 2 sides
  • Includes 2 pass-out ports
  • Splits around pipe or ducting for continuous cutting/working
  • Materials: PVC or Polyurethane
 
         
   
         
    LI-301 Single Chamber Work Containments "Doghouse Glovebag"

  • 27"H x 39"L x 24"W
  • 18" dia transfer sleeve
  • 14" x 16" access flap
  • 7 2" dia service sleeves
  • sets of glove port access sleeves

The "Doghouse" has become an industry standard and is widely used for assembly, maintenance, and repair work. Easy-to-use access ports and useful dimensions make the doghouse a popular ALARA tool. The LI-301 glovebag is used in conjunction with an external frame (LI-301F) and aluminum drip pan for support. The frame and glovebag assembly can also be mounted on a wheeled mounting frame for mobility.

 
         
 
         
    LI-301F Doghouse Glovebag External Frame and Drip Pan

The LI-301 can also be used with an aluminum transfer cylinder (LI-433) sized to fit the 18" transfer sleeve and attached directly to the external frame.

When fitted with 20" dia PVC sleeving (LI-620), objects can be securely transferred into or out of the Doghouse assembly.
 
         
 
         
    LI-302 Glovebag

  • 16" dia body with 15" high work chamber
  • 36" x 42" bottom flange flap with closure zipper
  • 12" zipper access opening
  • 2 pair of glove sleeve ports on side of chamber
  • 1 pair of glove sleeve ports on top of chamber

For use on large curved or flat surfaces. Bottom flap provides area to seal around work site for easy installation. Adequate space for small power tool operation. Can enclose pipes up to 12" dia size.

 
         
 
         
    LI-303 Glovebag

  • 24" dia body with 15" high work chamber
  • Installation sleeve for 4" or 9" dia mount
  • 12" zipper access opening
  • 2 pair of glove sleeve ports on side of chamber
  • 1 pair of glove sleeve ports on top of chamber

Bottom installation sleeve used for mounting onto fixed components. Adequate space for power tools. Designed for 2 person work.

 
         
 
         
    LI-304 Glovebag

  • 18" dia body with 24" long work chamber
  • 8" dia installation sleeves on both ends
  • Presslock zipper or Velcro closure runs length of bag
  • 12" zipper access opening
  • 1 pair of glove sleeve ports on each side of chamber

Splits in half to close around continuous piping run for installation.

 
         
 
         
    LI-305 Glovebag

  • 18" dia body with 15" high work chamber
  • Installation sleeves on bottom for 4" or 8" dia mount
  • 12" zipper access opening
  • 2 pair of glove sleeve ports on side of chamber
  • 1 glove sleeve port on top of chamber

Bottom installation sleeve can be fit to 2 different diameters for mounting onto fixed components. Top sleeve can be used for vent/filter or glove access.

 
         
 
         
    LI-306 Glovebag

  • 16" dia body with 15" high work chamber
  • 24" x 48" bottom flange flap with closure zipper
  • 12" zipper access opening
  • 3 glove sleeve ports on side of chamber
  • 1 glove sleeve port on top of chamber

Bottom flange flap enables installation around components in long continuous run work site. Good for total enclosure on pipe or valve body up to 8" diameter.

 
         
 
         
    LI-307 Glovebag

  • 46" long chamber with Velcro or zipper closure around 3" dia installation sleeves
  • 10" dia body with 1 glove sleeve access port on each end
  • 2 pair of glove sleeve ports on each side of chamber
  • 2 service sleeves
  • 12" chamber access zipper

For use on continuous pipe components up to 3" diameter. This versatile design has features that provide flexibility for many possible applications and configurations.

 
         
 
         
    LI-308 Glovebag

  • 12" dia body with 9" high work chamber
  • Installation sleeve on bottom for 5" dia mount
  • 2 glove sleeve ports on side of chamber
  • 1 glove sleeve port on top of chamber
  • 1 service sleeve

Good for use on small components on location. Installation sleeve can be oriented for mounting on top of component or sideways access to component.

 
         
 
         
    LI-309 Glovebag

  • 11" x 16" flange flap with closure zipper
  • Single glove sleeve port for access to work chamber
  • 9" access zipper and 1"dia service sleeve open to chamber

Best for use on flat or contoured surfaces to provide protection while working on or operating contaminated valves or guages.

 
         
 
         
    LI-310 Glovebag

  • 24" dia body and 15" high work chamber w/12" access zipper
  • Installation flange on bottom for 11-1/2" dia mount
  • 2 glove sleeve ports on top of chamber
  • 4 glove sleeve ports on side of chamber
  • 1 support ring

For installation on piping or other elongated items.

 
         
 
         
    LI-311 Glovebag

  • 30" dia body and 18" high work chamber w/12" access

    zipper

  • Dual installation sleeves on bottom: concentric 4" dia
    and 9" dia
  • 2 glove sleeve ports on top of chamber
  • 4 glove sleeve ports on side of chamber

Multiple size access sleeves for flexible use on different diameter piping systems.

 
         
 
         
    LI-312 Glovebag

  • 24" dia body and 15" high work chamber w/18" access

    zipper

  • 12" dia installation sleeve on bottom
  • 5 glove sleeve ports on side of chamber
  • 1 access sleeve port on top
  • 1 support ring

For mounting over large valve with offset installation sleeve to allow for shelf in chamber for tools on one side.

 
         
 
Products